MCE TV Philips 7135 Cardbus don't work
- Date: Tue, 29 Apr 2008 13:37:30 -0430
- From: Emilio Lazo Zaia <emiliolazozaia@xxxxxxxxx>
- Subject: MCE TV Philips 7135 Cardbus don't work
Hello,
I have purchased a "MCE TV Philips 7135 Cardbus" and I'm to set it up.
When I plug it, the module saa7134 is being loaded and dmesg says:
pccard: CardBus card inserted into slot 0
Linux video capture interface: v2.00
saa7130/34: v4l2 driver version 0.2.14 loaded
PCI: Enabling device 0000:06:00.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 17 (level, low) -> IRQ 17
saa7133[0]: found at 0000:06:00.0, rev: 209, irq: 17, latency: 0, mmio:
0x54000000
PCI: Setting latency timer of device 0000:06:00.0 to 64
saa7133[0]: subsystem: 1131:0000, board: UNKNOWN/GENERIC
[card=0,autodetected]
saa7133[0]: board init: gpio is e2c0c0
saa7133[0]: Huh, no eeprom present (err=-5)?
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0
Since card is not detected, I've typed some little bash script to unload
(rmmod) and load again saa7134 module with modprobe adding "card=n"
parameter with n from 1 to 117 and execute tvtime each time module is
being loaded with different card number (The tuner module I've not
reloaded with different values). Note that a message of no EEPROM
present is issued by saa7134 module! This is related specifically to
the tuner?
None of these 117 cards works in tv mode, some of these have not
"Television" input facility, others have "Composite1", "Composite2",
"S-Video" and some others have "TV (mono)" but in "Television" mode,
almost in all cases a blue screen is showed.
Here, the television norm is NTSC; I'm using Debian lenny with
2.6.24-amd64 kernel. Cardbus controller according to lspci is:
05:09.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus
Controller
and the output of "lspci -vv" regarding this TV card is:
06:00.0 Multimedia controller: Philips Semiconductors SAA7133/SAA7135
Video Broadcast Decoder (rev d1)
Subsystem: Philips Semiconductors Unknown device 0000
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (3750ns min, 9500ns max)
Interrupt: pin A routed to IRQ 17
Region 0: Memory at 54000000 (32-bit, non-prefetchable)
[size=2K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Anyone has this card working or has some idea about the correct
combination of card and tuner number?
TIA
Regards.
--
Emilio Lazo Zaia <emiliolazozaia@xxxxxxxxx>
Facultad de Ciencias, UCV
--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request@xxxxxxxxxx?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list